Products
-
T9100 Additive package for four-stroke engine oils
-
Zinc salt of dialkyldithiophosphoric acid based on secondary alkyl groups
-
T106A (TBN300) High alkaline linear alkyl benzene sulfonate calcium
-
T165A High molecular weight polyisobutylene succinimide
-
T202 Zinc salt of dialkyldithiophosphoric acid based on primary butyl and octyl groups
-
T115B (TBN250) High alkaline sulfided calcium alkyl phenate
-
High molecular weight emulsifier for emulsion explosives
-
T109D (TBN360) High alkaline calcium alkyl salicylate
-
T151B Borated polyisobutylene succinimide
-
T106D (TBN400) High alkaline synthetic calcium sulfonate based on long chain linear alkylbenzene
-
T5065 Additive package for thermal oils
-
T321Sulfided isobutylene
-
T8556 Organic molybdenum anti-friction additive
-
T2007A Polyisobutylene succinic anhydride
-
T205 Zinc salt of dialkyldithiophosphoric acid based on propyl, secondary and primary octyl groups
-
L135 Di-nonyldiphenylamine
T106Z (TBN330) High alkaline synthetic calcium dialkylbenzenesulfonate for lubricants
1、Alkalinity number (according to KOH) - not less than 330 mg KOH/g (according to the SH/T 0251 method); The high ability to neutralize acids provides oils and greases with a sufficient supply of alkalinity.
2、Calcium nanocarbonate micelles stabilization technology: after sulfonation, calcium treatment and carbonization, a stable system is formed. The retention of the alkaline number is at least 98%, and the stability of the indicators from batch to batch is ensured at the technology level.
3、Special modification for grease: The product is mainly for the preparation of grease, and can be used in the preparation of high-temperature bearing grease and other greases.
Description
marker
Product Description
T106Z (TBN 330) belongs to the class of detergent additives and is produced on the basis of dialkylbenzenesulfonic acid. In oils, the product has a high ability to neutralize acids and provides anti-corrosion protection. Detergent additives are the most common single additive in motor oil formulations: their main task is to neutralize acidic products formed during fuel combustion, inhibit the formation of piston carbon and varnish deposits, and protect against corrosion. The base number of T106Z (by KOH) is not less than 330 mg KOH/g, the kinematic viscosity at 100 °C is 60.00–200.0 mm²/s, the flash point in an open crucible is not lower than 175 °C, the mass fraction of sulfur is not less than 1.25%. The product is manufactured according to the corporate standard Q/YHT003-2015. It is intended primarily for the preparation of greases and can be used as a detergent in high-temperature bearing greases, as well as in the preparation of mid-range motor oils and marine oils.
Industry problem
When a customer is preparing greases for high-temperature operating conditions, insufficient detergent alkalinity or batch-to-batch variations mean that the finished lubricant cannot consistently neutralize the acidic oxidation products of the base oil and additives at high temperatures. As a result, the acid number can increase and metal surfaces are at risk of corrosion and rusting.
Solution
We offer high alkaline synthetic calcium dialkyl benzene sulfonate T106Z (TBN 330) for greases: the product provides anti-corrosion protection in oils. The T106 series uses technology to stabilize calcium nanocarbonate micelles: after sulfonation, calcium treatment and carbonation, a stable system is formed in which calcium sulfonate micelles envelop calcium nanocarbonate. Retention of the alkaline number is at least 98%, which guarantees the stability of indicators from batch to batch at the technology level. Base number (based on KOH) - not less than 330 mg KOH/g. Before shipment, products undergo quality control in accordance with state and corporate standards; Test reports are provided with the product.
Specifications
| Indicator | Norm | Test method |
| Appearance | Transparent brown-red liquid | Visual inspection |
| Flash point (open crucible), °C | ≥175 | GB/T 3536 |
| Kinematic viscosity at 100 °C, mm²/s | 60.00–200.0 | GB/T 265 |
| Base number (based on KOH), mg KOH/g | ≥330 | SH/T 0251 |
| Mass fraction of sulfur, % | ≥1.25 | SH/T 0303 |
Note:the product is manufactured according to the corporate standard Q/YHT003-2015. The recommended maximum processing temperature is not higher than 80 °C (176 °F), long-term storage temperature is not higher than 60 °C (140 °F). Safety precautions - see the relevant chemical safety data sheet.
Applications
Highly alkaline synthetic calcium dialkylbenzenesulfonate T106Z (TBN 330) is used mainly in the preparation of greases, mid-range motor oils and marine oils. The product can be used in the preparation of high temperature bearing greases and other greases; recommended dosage is 0.5–3.0% (by weight). We also provide customers with a full range of technical support - from the selection of individual additives and formulation to the delivery of ready-made additive packages.
About us
We have been operating since April 2018 and are a fine chemicals manufacturer specializing in the development, production and sale of lubricant additives. We have our own production: the area is about 46,667 m², the enterprise operates five lines for the production of additives for lubricants with a total capacity of 60,000 tons per year, the range includes more than 40 types of products. The production uses closed technological processes and intelligent control of the entire cycle: key parameters are controlled with an accuracy of ±0.5%, and the share of quality products reaches 99.9%.
We have our own development department; We also cooperate with universities and scientific institutes, constantly researching recipes and improving technologies. Our technical experts have provided services to companies such as Shell, BP, Castrol, Total, CNPC and Sinopec.
Service and guarantees
Pre-sales consultations and technical support:We provide free consultations and select a targeted solution, taking into account operating parameters and target characteristics, and do not just name the price according to the catalogue. We prepare a commercial offer within 2-3 working days after receiving full parameters; The quote itself is free.
Samples and trial batches:The client can request samples - they take 7-10 days to produce. We also accept trial orders in small quantities so that the client can check the characteristics and stability of the product before purchasing in industrial quantities.
Customization options:We manufacture products according to the specifications specified by the client, from the materials specified by him, with the application of our own logo and individual packaging. Regardless of the format - OEM or ODM - the details of cooperation are discussed with our commercial team.
Warranty and after-sales service:The warranty period is 3–5 years (the exact conditions are specified in the contract). We provide remote technical support and instructions for use; An instruction manual and documentation in English or Russian are supplied with the product. If defects are detected, the customer can submit a service request in the usual manner. In case of disagreement on quality, the parties, by agreement, send the problematic sample to an independent laboratory, and responsibility is determined based on the results of the examination.
Logistics and delivery
By default, we ship liquid products in 200 liter steel barrels or in tank containers (IBC); packaging meets export standards. Packing in wooden boxes without fumigation, neutral packaging, as well as customized solutions upon customer request are possible. All external packaging is completed with pallets and protective covers, which eliminates rolling, shock and moisture during transportation.
We work with three main modes of transport - sea, road and rail - as well as multimodal schemes (sea + railway, road + railway). If the client names his forwarder, we fully interact with him; If necessary, we will organize all transportation using our international logistics partners.
Payment is made by bank transfer (T/T), including for large orders. Volume discounts, OEM/ODM programs and exclusive distribution opportunities are available for wholesale buyers. Our principle is “mutually beneficial partnership and free technical support”: we regularly contact customers and, when updating products, offer options for switching to a new version.
Questions and answers
Question 1、How to choose a modification for your operating conditions?
Answer：It is enough to indicate the key parameters - type of working environment, operating pressure, operating temperature and installation conditions. Our team will suggest a suitable modification within 2-3 working days. If in doubt about your choice, you can first request samples for testing.
Question 2、Can lubricating oils of different brands and viscosities be mixed?
Answer：We do not recommend mixing: when mixing different viscosity classes, an unpredictable intermediate viscosity is obtained, and additive systems can interfere with each other. If the oil has already been topped up, change it completely as soon as possible and go back to one brand.
Question 3、What is the service life of the products?
Answer：Does it meet international standards? Service life depends on operating conditions; Under normal conditions, the product lasts for several years. Production is carried out in accordance with state and corporate standards; before shipment, full performance tests are carried out, and protocols are provided.
Question 4、Are the products suitable for high temperatures? And for short ones?
Answer：For high temperature conditions - yes. For regular low temp versions, no, if you want a low temp version, be sure to let us know before placing your order and we will custom make it after evaluation.
Question 5、Are you a manufacturer or trading company?
Answer：We are a manufacturer with our own production base and testing equipment. We invite clients to come and see for themselves.
Question 6、Is it possible to develop customized formulations and OEM/ODM cooperation?
Answer：Yes, we develop individual oil formulations for the operating conditions of the client’s equipment and provide OEM/ODM services. Contact us - we will be glad to cooperate.
contact us
Related Popular Products
T106D (TBN400) High alkaline synthetic calcium sulfonate based on long chain linear alkylbenzene
1、We use long-chain (C₂₀–₂₄) linear alkylbenzenesulfonic acid as raw materials; The product is suitable for the manufacture of calcium sulfonate grease, has a strong neutralizing ability, as well as detergent-dispersant and anti-corrosion effects. 2、Ultra-high alkaline formula: alkaline number - not lower than 395 mg KOH/g, retention of alkaline number - not less than 98%. Even when operating on high-sulfur fuel, the product contains a sufficient supply of acid neutralization. 3、The main application is medium and high-quality motor oils, as well as marine oils; The recommended dosage is 0.5–25% (mass fraction).
T204 Basic zinc salt of dialkyldithiophosphoric acid based on two primary octyl groups
1、High pH value. The product is a quality alkaline additive widely used for compounding anti-wear hydraulic oils, mid- and high-grade motor oils, and medium-speed marine oils. 2、Outstanding anti-wear properties. Under conditions of high loads and intense friction, this alkaline oil additive quickly forms a stable protective film, significantly reducing wear on metal surfaces and extending the service life of equipment. 3、Excellent compatibility. As a high-quality alkaline oil additive, the product is easily combined with base mono additives, including extreme pressure sulfur additives, and provides a synergistic effect in transmission and industrial gear oils.
T205 Zinc salt of dialkyldithiophosphoric acid based on propyl, secondary and primary octyl groups
1、The product is synthesized on the basis of thiophosphoric acid obtained from a mixture of primary and secondary alcohols - propyl and octyl: due to the excellent anti-wear properties of the oil and high hydrolytic stability, it is the main additive in gasoline oil for anti-wear and antioxidant protection of high-quality motor oils. 2、The content of sulfur, phosphorus and zinc - 16.00-18.50%, 8.00-9.50% and 9.00-10.80%, respectively - is maintained according to the corporate standard Q/YHT006-2015; Each batch undergoes full control at the exit from the factory, a test report is attached to the delivery, so the lubricating properties of the oil are stable from batch to batch. 3、Multifunctional base anti-wear additive with four functions - anti-oxidation, anti-wear, extreme pressure and anti-corrosion: protects the camshaft, tappets and cylinder liners, and is suitable for compounding high-quality motor oils with additives into gasoline oil.
T2007A Polyisobutylene succinic anhydride
1、The product is produced by thermal addition method from highly reactive polyisobutylene (Mn = 1000) and does not contain chlorine; ashless dispersants based on it are distinguished by excellent cleaning properties at high temperatures and good sludge dispersion at low temperatures. 2、This is an intermediate product of the succinic anhydride class, obtained by thermal addition: density 950 kg/m³, flash point 180 °C, kinematic viscosity 800 mm²/s, total acid number 110 mg KOH/g. 3、One product - several directions: based on it, bis-/polyalkenylsuccinimide and borated ashless dispersants are produced, as well as emulsifiers for emulsion explosives and technological additives for petrochemical production.
T5022 Anti-wear additive package for hydraulic oils
1、Meet stringent standards: The product is designed specifically for industrial hydraulic systems and fully meets the oil requirements of DIN 51524 and ISO 11158 standard. This ensures that the resulting oil when mixed has excellent anti-wear and anti-oxidation properties, effectively extending the life of equipment. 2、Versatile application: suitable for injection molding machines, machine tools and industrial hydraulic stations. Whether it is conventional HLP hydraulic oil or high-pressure systems, the product provides reliable protection for pumps and valves, adapting to a variety of severe operating conditions. 3、Flexible Formulation Solutions: We offer customized formulation support for different base oils and viscosity requirements. It can help you easily prepare high-quality HLP oil, effectively reduce your total procurement costs and improve the competitiveness of your blending plant.
Zinc salt of dialkyldithiophosphoric acid based on secondary alkyl groups
1、Three effects in one additive: antioxidant, anti-wear and corrosion protection. Zinc dithiophosphate (zddp) inhibits oil oxidation, prevents bearing corrosion and reduces cam lifter wear, providing comprehensive, all-around engine oil protection. 2、Light yellow transparent liquid, flash point not lower than 160 °C. Mass fraction of sulfur 14.0–16.0%, phosphorus 6.5–8.0%, zinc 6.5–9.0%, pH - no less than 5.80. The product is manufactured according to the corporate standard Q/YHT006, undergoes full control before shipment, and a test report is attached to each batch. 3、Own production: 5 technological lines, annual capacity 60,000 tons. The deviation of key parameters is kept within ±0.5%, the share of suitable products is 99.9%. Consistent quality from batch to batch, a balanced combination of performance characteristics, delivery speed and total purchasing costs.
T165A High molecular weight polyisobutylene succinimide
1、High molecular weight ashless dispersing agent with a nitrogen content of at least 1.90%: the product is obtained using thermal addition technology, it holds soot and sludge in suspension well, and is especially effective in dispersing low-temperature sludge. 2、Does not contain chlorine, alkaline number is not lower than 40.0 mg KOH/g; is produced according to the corporate standard Q/YHT007-2015 and is suitable for formulations of high-quality gasoline oils of API SH level and higher. 3、Based on highly active polyisobutylene and thermal joining technology: the product copes well with low-temperature sludge and soot, provides good detergent-dispersant efficiency and covers the needs for compounding oils of API SH class and higher.
T4209 Additive package for transmission oils
1、The additive is made from high-quality extreme pressure, anti-wear and anti-oxidation components and provides a complex effect: 75w90 gear oil and GL-4 gear oil derived from it under severe operating conditions - high-speed shock loads and high torque - effectively prevent scuffing, wear, pitting and peeling of teeth, as well as their corrosion. 2、Production is carried out using hermetic technology with intelligent control of the entire process: the deviation of key parameters does not exceed ±0.5%, the share of suitable products reaches 99.9%. Before shipment, each batch undergoes full control, a test report is attached to the delivery - the quality is fully controlled and traceable. 3、Products are produced in-house: five production lines provide an annual capacity of 60,000 tons. We accept trial orders, provide volume discounts and work under OEM/ODM schemes - this allows us to offer an individual solution with a balance between characteristics, delivery time and total purchase cost.
T109D (TBN360) High alkaline calcium alkyl salicylate
1、High base number (340-380 mg KOH/g) and powerful acid neutralization: the product provides alkalinity reserve for heavy diesel oils, oils with extended drain intervals and operating conditions on high sulfur content fuels. 2、Excellent cleaning properties and thermal stability at high temperatures inhibit carbon deposits and varnish deposits on the piston; light color and low viscosity (≤50 mm²/s at 100 °C) simplify the introduction of the product into the formulation. 3、Good oil solubility, compatibility with sulfonates and hydrolytic stability facilitate compounding with other single additives; The product works effectively in combination with an antioxidant additive, extending oil life.
T5065 Additive package for thermal oils
1、Contains a highly effective antioxidant and metal deactivator in combination with other additives. The package is specially designed for compounding thermal oils with an operating temperature of 250–300 °C: the finished product is distinguished by high thermal-oxidative stability and reliable anti-corrosion protection, and its service life is significantly increased. 2、Recommended dosage is 0.8-2.0%. When using base oils of groups II and III, the input rate can be reduced, which gives coolant oil manufacturers a flexible reserve to optimize the cost of the formulation. 3、Reliable delivery: shipment within 7-10 days after signing the contract and payment; sea, land and rail transportation, as well as multimodal schemes; delivery to Russia and Central Asia - about 15–20 days; Urgent shipment with end-to-end cargo tracking is possible.
T203 Zinc salt of dialkyldithiophosphoric acid based on two primary octyl groups
1、The additive is made from thiophosphoric acid obtained on the basis of octanol: the structure of the zinc salt provides excellent thermal stability and reliable anti-wear and antioxidant protection in medium and high-class diesel oils, featuring high thermal-oxidative stability. 2、Hydrolytic stability and antioxidant properties are excellent: the content of sulfur, phosphorus and zinc is strictly controlled according to corporate standards, the flash point is not lower than 180 ° C, so the product is suitable for anti-wear hydraulic oil formulations as hydraulic oil additives. 3、Each batch undergoes full control according to the corporate standard Q/YHT006-2015 and is accompanied by a test report; As a gear oil additive, the product is stable from batch to batch and helps balance costs when purchasing in bulk.
High molecular weight emulsifier for emulsion explosives
1、The product is based on highly active polyisobutylene succinic anhydride; it is suitable for lines for the production of emulsion explosives of any configuration, characterized by small micelles and good emulsifying ability during use. 2、The emulsion explosives obtained on its basis are water-resistant and acid-resistant, stable during storage and have good pumpability; The recommended dosage is 1.0–2.0%. 3、The finished explosive emulsion is homogeneous and stable; The product is equally suitable for bulk and packaged lines. Production is localized, the supply chain is streamlined, which allows us to find a balance between quality, delivery time and the total cost of purchase.
L57 Octylbutyldiphenylamine
1、High anti-oxidation efficiency at high temperatures. Significantly increases the thermal stability of hot oils, effectively inhibits the increase in viscosity in high-quality motor oils and extends the drain interval. 2、Excellent compatibility. In composition with aromatic amines and sterically hindered phenols, it exhibits a synergistic effect. It is a basic component of high-quality additives for hydraulic oils. 3、Excellent high temperature thermal stability. The liquid form is convenient for dosing. Suitable for turbine oils, coolants and other industrial oils, ensuring trouble-free long-term operation of equipment.
T2022 Additive package for two-stroke engine oils
1、To prepare two-stroke oil of the JASO FC class, only 2.2% (mass fraction when added to the oil) is sufficient - the dosage is highly economical, and bulk purchases allow you to effectively control the costs of the additive package and formulation. 2、Detergency and low smoke, high oil film strength: The product prevents clogging of the motorcycle exhaust system, reduces metal-to-metal wear, and extends engine life without loss of power. Suitable for oil for two-stroke engines with fuel injection and pre-mixing of fuel and oil. 3、Semi-synthetic two-stroke engine oil formulation, prepared with a small amount of polyisobutylene (molecular weight 1000) and a high flash point diluent, provides performance above the requirements of the Japanese JASO FC standard.
T202 Zinc salt of dialkyldithiophosphoric acid based on primary butyl and octyl groups
1、The raw materials and technology are transparent: the product is obtained from thiophosphoric acid, synthesized on the basis of butanol and octanol. It combines antioxidant, anti-wear and anti-corrosion effects and is suitable for motor, transmission and hydraulic oil formulations. 2、The product is suitable for compounding transmission oils and is considered as one of the options when selecting additives for transmission oils; recommended dosage is 0.5–3.0% (by weight). 3、Thermal stability is at a good level: the flash point in an open crucible is not lower than 180 °C, and the content of sulfur, phosphorus and zinc is standardized by clear indicators, which simplifies the selection according to the technical data sheet and the target recipe.
L135 Di-nonyldiphenylamine
1、High-temperature amine antioxidant with increased resistance: based on diphenylamine, which at high temperatures continuously suppresses the late stage of oxidation of motor oil and lasts longer than conventional bulk-hindered phenols, increasing the oil change interval. 2、Good compatibility and synergistic effect. In combination with other aromatic amines and bulk-hindered phenols, mutual reinforcement occurs, making the product suitable for formulations of premium motor oils, thermal oils, transformer oils and greases. 3、Excellent thermal stability at high temperatures. As an additive for hydraulic oil, it is used in high-temperature hydraulic systems of injection molding machines and steel-casting machines; At the same time, it inhibits the growth of the acid number of transformer oil.