Products
-
T3358 Additive package for turbine oils
-
T104A (TBN25) Synthetic low base number calcium alkyl benzene sulfonate
-
T109D (TBN360) High alkaline calcium alkyl salicylate
-
Zinc salt of dialkyldithiophosphoric acid based on secondary alkyl groups
-
T2007A Polyisobutylene succinic anhydride
-
T151B Borated polyisobutylene succinimide
-
L135 Di-nonyldiphenylamine
-
T106A (TBN300) High alkaline linear alkyl benzene sulfonate calcium
-
T106D (TBN400) High alkaline synthetic calcium sulfonate based on long chain linear alkylbenzene
-
T202 Zinc salt of dialkyldithiophosphoric acid based on primary butyl and octyl groups
-
T154A Polyisobutylene succinimide
-
T5033 Ashless anti-wear additive package for hydraulic oils
-
T115B (TBN250) High alkaline sulfided calcium alkyl phenate
-
T321Sulfided isobutylene
-
T3259 Additive package for heavy-duty diesel engine oils
-
T203 Zinc salt of dialkyldithiophosphoric acid based on two primary octyl groups
T4209 Additive package for transmission oils
1、The additive is made from high-quality extreme pressure, anti-wear and anti-oxidation components and provides a complex effect: 75w90 gear oil and GL-4 gear oil derived from it under severe operating conditions - high-speed shock loads and high torque - effectively prevent scuffing, wear, pitting and peeling of teeth, as well as their corrosion.
2、Production is carried out using hermetic technology with intelligent control of the entire process: the deviation of key parameters does not exceed ±0.5%, the share of suitable products reaches 99.9%. Before shipment, each batch undergoes full control, a test report is attached to the delivery - the quality is fully controlled and traceable.
3、Products are produced in-house: five production lines provide an annual capacity of 60,000 tons. We accept trial orders, provide volume discounts and work under OEM/ODM schemes - this allows us to offer an individual solution with a balance between characteristics, delivery time and total purchase cost.
Description
marker
Product Description
The T4209 transmission oil additive package is a complex additive made from high-quality extreme pressure, anti-wear and antioxidant components. It is designed for oil mixing plants: it is enough to add the additive to the base oil in the recommended proportion to obtain the finished product. The package is used for the preparation of 75w90 transmission oil, as well as gear oils and manual transmission oils of viscosity classes SAE90, 80W/90, 85W/90, 85W/140. The oil prepared on its basis under harsh conditions - high-speed shock loads and high torque - reliably prevents scuffing, wear, pitting and flaking on the surface of the teeth, and also protects it from corrosion. Recommended dosages by quality class: CKC - 1.1%, CKD - 1.5%, GL-4 - 2.1%, GL-5 - 4.2% (according to internal calculations); The additive is suitable for preparing oils based on base oils of groups I and II.
Typical problem
If the key properties of an additive package, such as extreme pressure and anti-wear, “float” from batch to batch, the finished oil produced according to the same recipe has difficulty achieving stable compliance with standards. If anti-wear and extreme pressure protection are insufficient under conditions of high-speed shock loads and high torque, the teeth will experience scuffing, wear, pitting, flaking and corrosion.
Our solution:
We use hermetic production technology and intelligent control of the entire process: key technological parameters are controlled with a deviation of no more than ±0.5%, and the proportion of suitable products reaches 99.9%.
The requirements of the formulation are covered by a rational combination of functional components - extreme pressure, anti-oxidation and anti-corrosion. The sulfur-containing extreme pressure component quickly forms a boundary film under high and shock loads, preventing galling and scoring of the teeth, while the anti-wear and anti-oxidation components protect the tooth surface and inhibit oil oxidation.
Specifications
Recommended dosages by quality class (according to internal calculations, % by weight):
| Quality class | Dosage, % |
| CKC | 1.1 |
| CKD | 1.5 |
| GL-4 | 2.1 |
| GL-5 | 4.2 |
The additive is suitable for preparing SAE90, 80W/90, 85W/90, 85W/140 oils based on group I and II base oils.
Typical quality indicators:
| Indicator | Typical value | Test method |
| Density at 20 °C, kg/m³ | actual value | GB/T1884 |
| Flash point (open crucible), °C | 100 | GB/T3536 |
| Kinematic viscosity at 100 °C, mm²/s | 6 | GB/T265 |
| Mass fraction of phosphorus, % | 0.9 | SH/T0296 |
| Mass fraction of sulfur, % | 35 | GB/T388 |
| Mass fraction of nitrogen, % | 0.3 | SH/T0224 |
| Mechanical impurities,% | 0.1 | GB/T511 |
Packaging and storage:the additive is supplied in metal barrels of 200 liters; avoid contact with strong oxidizing agents; storage temperature - no higher than 50 °C; prevent the ingress of water and impurities. Packaging, labeling, transportation, storage and acceptance - according to SH/T0164. Accurate indicators are confirmed by the test report supplied with the product.
Applications
The product is designed for oil mixing plants, grease manufacturers and other customers. T4209 is used for the preparation of GL-4 gear oils and GL-5 class manual transmission oils, as well as gear oils of viscosity classes 75W-90, 80W/90, 85W/90, 85W/140; the dosage is determined by the quality class (GL-4 - 2.1%, GL-5 - 4.2%, according to internal calculations). The finished oil is suitable for modes with increased requirements for synchronizer protection; Similar formulation solutions are used in industrial gearboxes - medium and heavy-duty gearboxes, gear mechanisms. The customer can select the product directly by oil type, vehicle or equipment operating mode and target characteristics; a team of developers and technical support is ready to help with the selection, adaptation to application and development of individual solutions.
About us
The company has been operating since April 2018. Our own production site occupies approximately 46,667 m²: there are five lines for the production of lubricating oil additives with an annual capacity of 60,000 tons and a range of more than 40 items. The staff includes over 80 employees: 12 engineering and technical specialists, 9 developers and 45 production workers.
Our technical team has provided services to companies such as Shell, BP, Castrol, Total, CNPC and Sinopec and therefore has extensive knowledge of the products and lubricant market requirements.
Thanks to our own production and a well-functioning supply chain, we offer the client a balanced solution regarding product characteristics, delivery time and total purchase cost.
Service and guarantees
Product selection is carried out in a targeted manner, taking into account operating parameters, oil type and target class; technical consultations are free, a commercial proposal is prepared within 2-3 business days. Samples are produced in 7-10 days, trial orders are accepted in small quantities. The order goes into production in 3–5 days and is shipped in 7–10 days; Urgent shipment is possible.
Inspection at the factory or by a third party is acceptable. The warranty period is determined by the contract; Remote technical support is provided, and disputed batches are sent for independent examination to a third-party laboratory. Payment - bank transfer (T/T); There are volume discounts for wholesale buyers, and OEM/ODM cooperation channels are available.
Logistics and delivery
As a rule, products are shipped in 200 liter steel drums or tank containers (IBC) in export packaging: pallets and protective covers protect the containers from displacement, shock and moisture. Customer's logo, neutral packaging and fumigation-free wooden boxes are available; Labels and packing slips are included with the shipment.
Delivery is carried out by sea, land and rail, as well as through multimodal schemes; We also work with the forwarder specified by the client. Shipment - 7–10 days after signing the contract and receiving advance payment; Delivery to Russia and Central Asia takes about 15–20 days, urgent shipment is possible.
We provide end-to-end cargo tracking, insure transportation upon request and provide a full set of transport documents - bill of lading, waybills and others.
Questions and answers
Question 1、What industries are the products used in?
Answer:The products are widely used in the oil and gas and chemical industries, mainly in the production of automotive transmission oils - for manual transmissions and rear axles; The range covers API classes GL-4 and GL-5 (for example, 75W-90, 80W-90). Production is carried out using hermetically sealed technology with intelligent control of the entire process: the deviation of key parameters does not exceed ±0.5%, the share of suitable products is 99.9%. Detailed differences are given in the product data sheet.
Question 2、How to choose a product for your operating conditions?
Answer:It is enough to provide key parameters - oil type, target class (for example, API GL-4) and application conditions, and our team will offer a suitable product within 2-3 business days. If you are in doubt about your choice, you can first order samples for testing.
Question 3、Can oils of different brands and viscosities be mixed?
Answer:We do not recommend mixing. Adding different viscosity grades results in unpredictable intermediate viscosities, and additive systems can conflict. After topping up, you should completely change the oil as soon as possible and return to one brand. Before switching to oil from another manufacturer, we recommend thoroughly flushing the system with flushing oil.
Question 4、Are you a manufacturer or trading company? What is the minimum order quantity?
Answer:We are a manufacturer: we have our own production workshops and testing equipment. The minimum order quantity is one ton; We invite customers to visit the production and see for themselves.
contact us
Related Popular Products
T5022 Anti-wear additive package for hydraulic oils
1、Meet stringent standards: The product is designed specifically for industrial hydraulic systems and fully meets the oil requirements of DIN 51524 and ISO 11158 standard. This ensures that the resulting oil when mixed has excellent anti-wear and anti-oxidation properties, effectively extending the life of equipment. 2、Versatile application: suitable for injection molding machines, machine tools and industrial hydraulic stations. Whether it is conventional HLP hydraulic oil or high-pressure systems, the product provides reliable protection for pumps and valves, adapting to a variety of severe operating conditions. 3、Flexible Formulation Solutions: We offer customized formulation support for different base oils and viscosity requirements. It can help you easily prepare high-quality HLP oil, effectively reduce your total procurement costs and improve the competitiveness of your blending plant.
T205 Zinc salt of dialkyldithiophosphoric acid based on propyl, secondary and primary octyl groups
1、The product is synthesized on the basis of thiophosphoric acid obtained from a mixture of primary and secondary alcohols - propyl and octyl: due to the excellent anti-wear properties of the oil and high hydrolytic stability, it is the main additive in gasoline oil for anti-wear and antioxidant protection of high-quality motor oils. 2、The content of sulfur, phosphorus and zinc - 16.00-18.50%, 8.00-9.50% and 9.00-10.80%, respectively - is maintained according to the corporate standard Q/YHT006-2015; Each batch undergoes full control at the exit from the factory, a test report is attached to the delivery, so the lubricating properties of the oil are stable from batch to batch. 3、Multifunctional base anti-wear additive with four functions - anti-oxidation, anti-wear, extreme pressure and anti-corrosion: protects the camshaft, tappets and cylinder liners, and is suitable for compounding high-quality motor oils with additives into gasoline oil.
T165A High molecular weight polyisobutylene succinimide
1、High molecular weight ashless dispersing agent with a nitrogen content of at least 1.90%: the product is obtained using thermal addition technology, it holds soot and sludge in suspension well, and is especially effective in dispersing low-temperature sludge. 2、Does not contain chlorine, alkaline number is not lower than 40.0 mg KOH/g; is produced according to the corporate standard Q/YHT007-2015 and is suitable for formulations of high-quality gasoline oils of API SH level and higher. 3、Based on highly active polyisobutylene and thermal joining technology: the product copes well with low-temperature sludge and soot, provides good detergent-dispersant efficiency and covers the needs for compounding oils of API SH class and higher.
T161B Borated high molecular weight polyisobutylene succinimide with high viscosity and high nitrogen content
1、Compatible with the formulations of gasoline motor oils of API SG classes and higher, as well as API CF-4 diesel oils and higher; especially in demand in environmentally friendly motor oil formulas. The recommended dosage is 2.0–5.0% (by weight). 2、Effectively inhibits the growth of engine oil viscosity, combines anti-oxidation and anti-wear properties, improves oil compatibility with fluorine rubber seals and reduces high-temperature corrosion of copper-lead liners. The product does not contain chlorine. 3、Own production: five lines with an annual capacity of 60,000 tons, deviation of key parameters - no more than ±0.5%, share of suitable products - 99.9%. We maintain a balance between characteristics, delivery times and the total cost of the purchase.
T3358 Additive package for turbine oils
1、Compatible with viscosity grades 5W-30, 5W-40 and others, meets API SN, ILSAC GF-5 and JASO MA2 requirements. This additive package is the optimal solution for effective compounding. 2、At a dosage of 8.5%, it allows you to obtain all-season oils from base oils of groups II and III. As a specialized oil additive package, it has excellent detergent-dispersant properties. 3、Combines detergent additives, ashless dispersants and anti-oxidation/extreme pressure components. This engine oil additive package effectively suppresses the formation of sludge and varnish deposits, extending oil change intervals.
T2007A Polyisobutylene succinic anhydride
1、The product is produced by thermal addition method from highly reactive polyisobutylene (Mn = 1000) and does not contain chlorine; ashless dispersants based on it are distinguished by excellent cleaning properties at high temperatures and good sludge dispersion at low temperatures. 2、This is an intermediate product of the succinic anhydride class, obtained by thermal addition: density 950 kg/m³, flash point 180 °C, kinematic viscosity 800 mm²/s, total acid number 110 mg KOH/g. 3、One product - several directions: based on it, bis-/polyalkenylsuccinimide and borated ashless dispersants are produced, as well as emulsifiers for emulsion explosives and technological additives for petrochemical production.
T115B (TBN250) High alkaline sulfided calcium alkyl phenate
1、High acid-neutralizing ability: base number - 245–265 mg KOH/g. The product is used in the manufacture of medium and high-class motor oils, especially turbodiesel, and helps control the formation of carbon deposits on the piston. 2、Recommended dosages are clearly specified: 0.5-4.0% for motor oils and 25-35% for marine cylinder oil (mass fraction). The additive is easily added to the formulation and is compatible with other detergent additives and ashless dispersants. 3、We use a closed technological scheme and intelligent control at all stages of production: fluctuations in key parameters do not exceed ±0.5%, the share of quality products reaches 99.9%. Custom manufacturing (OEM/ODM) and test samples are available.
T202 Zinc salt of dialkyldithiophosphoric acid based on primary butyl and octyl groups
1、The raw materials and technology are transparent: the product is obtained from thiophosphoric acid, synthesized on the basis of butanol and octanol. It combines antioxidant, anti-wear and anti-corrosion effects and is suitable for motor, transmission and hydraulic oil formulations. 2、The product is suitable for compounding transmission oils and is considered as one of the options when selecting additives for transmission oils; recommended dosage is 0.5–3.0% (by weight). 3、Thermal stability is at a good level: the flash point in an open crucible is not lower than 180 °C, and the content of sulfur, phosphorus and zinc is standardized by clear indicators, which simplifies the selection according to the technical data sheet and the target recipe.
T154A Polyisobutylene succinimide
1、Ashless succinimide additive made from highly reactive polyisobutylene (Mn=1000) using thermal addition technology: the product does not contain chlorine and inhibits the formation of carbon deposits on pistons and varnish deposits. 2、Excellent detergent-dispersant properties: soot, sludge and varnish precursors formed during fuel combustion are kept suspended in the oil, which prevents varnish deposits from settling in the engine on the piston rings, in the oil passages and on the valve mechanism. 3、Suitable for compounding medium and high quality diesel and gasoline motor oils, as well as cylinder oils for low speed crosshead marine engines; especially recommended for environmentally friendly motor oils. The recommended dosage is 2.0–4.0% (by weight).
T2022 Additive package for two-stroke engine oils
1、To prepare two-stroke oil of the JASO FC class, only 2.2% (mass fraction when added to the oil) is sufficient - the dosage is highly economical, and bulk purchases allow you to effectively control the costs of the additive package and formulation. 2、Detergency and low smoke, high oil film strength: The product prevents clogging of the motorcycle exhaust system, reduces metal-to-metal wear, and extends engine life without loss of power. Suitable for oil for two-stroke engines with fuel injection and pre-mixing of fuel and oil. 3、Semi-synthetic two-stroke engine oil formulation, prepared with a small amount of polyisobutylene (molecular weight 1000) and a high flash point diluent, provides performance above the requirements of the Japanese JASO FC standard.
T8556 Organic molybdenum anti-friction additive
1、Energy saving: As a highly effective friction modifier, the product forms a boundary lubricating film on friction surfaces, which can significantly reduce the coefficient of friction, fuel consumption and cylinder wear. 2、Synergy of components: being a high-quality molybdenum additive, the product, when used together with antioxidant and anti-corrosion additives of the ZDDP series, as well as with aromatic amine antioxidants, gives a pronounced synergistic effect in terms of anti-wear and antioxidant properties. 3、Eco-friendly formulation: The product does not contain sulfur and phosphorus, has excellent oil solubility and, as an environmentally friendly molybdenum additive, is suitable for the production of high-quality gasoline and diesel engine oils and environmentally friendly lubricants, fully satisfying the most stringent environmental requirements.
L135 Di-nonyldiphenylamine
1、High-temperature amine antioxidant with increased resistance: based on diphenylamine, which at high temperatures continuously suppresses the late stage of oxidation of motor oil and lasts longer than conventional bulk-hindered phenols, increasing the oil change interval. 2、Good compatibility and synergistic effect. In combination with other aromatic amines and bulk-hindered phenols, mutual reinforcement occurs, making the product suitable for formulations of premium motor oils, thermal oils, transformer oils and greases. 3、Excellent thermal stability at high temperatures. As an additive for hydraulic oil, it is used in high-temperature hydraulic systems of injection molding machines and steel-casting machines; At the same time, it inhibits the growth of the acid number of transformer oil.
T107 (TBN400) Highly alkaline synthetic magnesium sulfonate based on long-chain linear alkylbenzene
1、Low ash content. As a magnesium sulfonate detergent, the product effectively controls oil ash content: with a TBN of at least 395 mg KOH/g, it has excellent acid suppression properties and is an ideal base ingredient for the preparation of low ash oils. 2、Low turbidity and low sediment value: the product significantly reduces the deposition of impurities during oil storage and operation, reducing filtration costs and the risk of equipment clogging. 3、Detergency and corrosion protection: The additive is made from long-chain (C20-24) linear alkylbenzenesulfonic acid and provides good detergent, dispersant and anti-corrosion properties.
T109D (TBN360) High alkaline calcium alkyl salicylate
1、High base number (340-380 mg KOH/g) and powerful acid neutralization: the product provides alkalinity reserve for heavy diesel oils, oils with extended drain intervals and operating conditions on high sulfur content fuels. 2、Excellent cleaning properties and thermal stability at high temperatures inhibit carbon deposits and varnish deposits on the piston; light color and low viscosity (≤50 mm²/s at 100 °C) simplify the introduction of the product into the formulation. 3、Good oil solubility, compatibility with sulfonates and hydrolytic stability facilitate compounding with other single additives; The product works effectively in combination with an antioxidant additive, extending oil life.
T106A (TBN300) High alkaline linear alkyl benzene sulfonate calcium
1、High acid-neutralizing ability. In additive formulations for diesel oils, the product is used as a detergent additive; It effectively neutralizes acids and is suitable for the preparation of medium and high-grade motor oils, as well as marine oils. 2、Detergent-dispersant effect and corrosion protection. Products of the T106A line have detergent-dispersant properties and anti-corrosion characteristics in oil systems; they are recommended for formulations of motor and marine oils, which are subject to increased purity requirements. 3、Clear indicators - convenient for recipe mixing. The total alkaline number (in terms of KOH) is 295–310 mg/g, the recommended dosage is 0.5–3.0%; the customer can independently evaluate the introduction of the product based on the base oil and the recipe system.
High molecular weight emulsifier for emulsion explosives
1、The product is based on highly active polyisobutylene succinic anhydride; it is suitable for lines for the production of emulsion explosives of any configuration, characterized by small micelles and good emulsifying ability during use. 2、The emulsion explosives obtained on its basis are water-resistant and acid-resistant, stable during storage and have good pumpability; The recommended dosage is 1.0–2.0%. 3、The finished explosive emulsion is homogeneous and stable; The product is equally suitable for bulk and packaged lines. Production is localized, the supply chain is streamlined, which allows us to find a balance between quality, delivery time and the total cost of purchase.